Human Machine Interface (HMI)

A human machine interface (HMI) is the display system, usually graphical, that operators use to monitor process variables and acknowledge alarms, and to control equipment in real time. Response speed depends on the controller and network behind it. HMIs range from local, panel-mounted touchscreens on one machine to networked operator workstations that show the whole site to a control room. Standards like ISA-101 give design guidance that helps keep screens consistent and easy to read, which supports effective operator decision-making in normal and abnormal conditions.

Vista Projects is a multi-disciplinary engineering and system integration firm based in Calgary, Alberta. It has worked on complex capital projects in the energy industry since 1985, and one lesson keeps coming up: an HMI works best on day one when the data behind it is right early and kept in one place.

What Is a Human Machine Interface?

A human machine interface (HMI) is the point where a person and an automated process trade information. At an industrial site, it pairs display hardware, like a touchscreen or industrial PC, with HMI software. The software turns live controller data into graphics and trends, along with alarm messages. The operator reads the screen, then sends commands back, like starting a pump or changing a setpoint.

It’s a broad term, and in a general sense a car dashboard counts as a human machine interface too. In process and energy plants, “HMI” commonly means the operator interface to a control system. HMIs also serve standalone machines and packaged equipment.

An HMI is not the controller. Control logic, including PID loops and interlocks, runs in a programmable logic controller (PLC) or a distributed control system (DCS). Safety functions run in a safety instrumented system, which is often separate from the control system. The HMI shows what those systems are doing and passes along the operator’s requests.

How an HMI Works

An HMI reads and writes data points in the control system. Many platforms call these tags. Field instruments measure pressure, temperature, level, and flow, and the controller holds each value in memory. The HMI typically reads those values over an industrial network, sometimes through an OPC server or gateway. OPC UA and Modbus TCP are common protocols, as is EtherNet/IP. When an operator enters a command, the HMI sends it to the controller, and the control system’s interlocks and modes, along with its own validation, decide whether it’s carried out.

This has two practical consequences. The first is that the controller can keep running if the HMI fails, as long as the controller and network stay healthy and control doesn’t depend on the screen. Operators at that station still lose sight of the process and the ability to step in from it, so depending on risk assessments, sites add redundant operator stations and hardwired shutdown buttons, along with procedures for display failure.

The second is that the screen is only as good as its data. A failed transmitter or a dropped link can leave a value that looks normal but is stale, and a wrongly mapped tag can show the wrong value entirely. Depending on configuration, a lost link can freeze or blank the last value, or flag it. Good displays mark bad-quality data clearly.

What an HMI Does: Core Functions

Most industrial HMIs handle some or all of five jobs, depending on how they’re configured. Monitoring is the most basic. The HMI shows selected live process variables so the operator can see at a glance if the process is on track. On control-capable HMIs, authorized users also start and stop equipment, open and close valves, switch loops between manual and automatic, and change setpoints.

Alarm handling announces abnormal conditions with sound and colour, and operators acknowledge alarms and see which are still active. Many platforms also offer alarm shelving under controlled rules. Trending plots configured values over time so operators can spot a slow drift, while longer-term records may sit in a process historian or a local log. The last job is event logging and access control. Configured logging time-stamps alarms and operator actions, and role-based access, where set up, limits what each user can change.

Types of Human Machine Interfaces

Local Panel-Mounted HMIs

Panel-mounted HMIs are usually touchscreens on a control panel or packaged equipment skid, used right at the equipment. Outdoor panels need an enclosure rating suited to the conditions, such as Type 4X or IP66. Panels in classified areas also need hazardous location certification. In Canada, Section 18 of the Canadian Electrical Code (CSA C22.1) sets the rules for hazardous locations.

Control Room Operator Workstations

Central control rooms run on operator workstations, often multi-monitor consoles tied to the plant’s DCS or SCADA servers. In some plants, one operator watches several process units from one console, so screen layout and navigation matter a great deal, and so does the way alarms are presented.

Remote, Web, and Mobile HMIs

Pipelines and gathering systems cover a lot of ground, as do well pads. They commonly use SCADA HMIs to supervise remote sites from one central location. Web and mobile HMIs put views on tablets and phones, from read-only to full control, depending on setup and permissions.

Hardwired Panels and Annunciators

Older control rooms used hardwired panels of gauges, push buttons, indicator lights, and annunciator windows. Some sites still keep one for critical functions, like an emergency shutdown button designed to work without the graphical HMI.

HMI vs PLC, DCS, and SCADA

An HMI is the operator’s window on a control system, not a control system by itself. It’s commonly paired with all three of the systems below, though not every PLC has one. If the HMI fails, a properly designed PLC keeps the process running. If the PLC fails, the equipment should go to the fault state its designers defined, or an independent safety system acts.

SystemMain jobTypical scopeWhere the HMI fits
PLCRuns control logic for a machine or packageOne machine, skid, or process areaA local panel or workstation, where fitted, reads and writes PLC data
DCSCoordinates continuous process control across a plantA whole site or large process unitsOperator workstations are part of the DCS itself
SCADASupervises and controls dispersed sitesPipelines, well pads, and gathering systemsCentral screens show data gathered from remote PLCs and RTUs
HMILets people monitor and operate the processAny of the aboveIt is the presentation layer when one is used

For more on supervisory systems, see SCADA architecture in our terminology glossary.

What Makes a Good HMI: ISA-101, IEC 63303, and High-Performance Design

ANSI/ISA-101.01-2015, Human Machine Interfaces for Process Automation Systems, is a leading North American standard for HMI design (ISA overview). Published in July 2015, it covers the HMI lifecycle from philosophy and design through implementation, operation, and maintenance. In August 2024, the IEC published IEC 63303:2024 (IEC listing), an international standard based on ANSI/ISA-101.01 with a similar lifecycle approach. On Canadian projects that specify them, these standards guide screen design. The Canadian Electrical Code (CSA C22.1) and CSA Z462 cover installation and electrical safety.

The HMI Philosophy, HMI Style Guide, and Toolkit

ISA-101 doesn’t impose one set of colours and symbols. Instead, it asks each owner to define three things of its own. The HMI philosophy sets out the site’s HMI principles and goals, not tied to any platform, plus who is in charge of what. The HMI style guide then shows how those principles apply on a specific control system platform, typically covering colours, symbols, fonts, and layouts. The HMI toolkit is a library of reusable graphic objects and faceplates built to match the style guide.

ISA’s technical report ISA-TR101.01-2022 gives practical guidance on writing the HMI philosophy.

The HMI Display Hierarchy

Projects aligned with ISA-101 sort screens in a display hierarchy of up to four levels. Level 1 shows the operator’s whole area at a glance. Level 2 covers one process unit for normal operation. Level 3 gives detail on a single piece of equipment for troubleshooting. Level 4 includes diagnostic and support information, such as interlock status and procedures. Operators drill down only as far as the situation calls for.

High-Performance HMI Principles

A high-performance HMI helps operators notice and understand problems fast, rather than copying a piping and instrumentation diagram. A common convention, drawn from ASM Consortium guidance, uses a neutral grey background and saves colour for abnormal conditions and alarms. It adds analogue indicators that show a value against its normal range, along with embedded trends, and keeps the layout consistent.

Why HMI Design Matters: Lessons From Abnormal Situations

Two incidents show what happens when an operator interface gives people the wrong picture. One study shows the payoff of getting it right.

Three Mile Island, 1979

In 1979, a relief valve at Three Mile Island Unit 2 stuck open, but a control room light suggested it had closed (NRC backgrounder). The light only showed that a close signal had been sent. Operators acted on the wrong picture while about 100 alarms went off within minutes. An indication has to show what it appears to show.

Milford Haven, 1994

On 24 July 1994, an explosion and fires at the Texaco refinery in Milford Haven, Wales, injured 26 people. The UK Health and Safety Executive investigation found three problems. A shut valve showed as open, and the graphics gave no useful overview. On top of that, there were too many alarms, and they were badly prioritized. In the final 11 minutes, two operators faced at least 275 alarms (HSE information sheet), and some records were overwritten. HSE estimated rebuilding costs at around £48 million. 

What a Better Operator Interface Achieves

In 2004 tests at a North American ethylene plant, NOVA Chemicals supported 21 experienced operators as they worked through comparable simulated upsets (published ASM Consortium study). Some used traditional graphics, and others used displays based on Abnormal Situation Management (ASM) Consortium research. With ASM-style displays, operators spotted problems before the first alarm 48% of the time, against 10% on traditional graphics. Their success rate rose from 70% to 96%. The same ASM Consortium paper reports task times falling from 18.1 minutes to 10.6 minutes, a 41% reduction. The study predates ISA-101.

Alarm Management and ISA-18.2 Benchmarks

ANSI/ISA-18.2-2016 and EEMUA 191 treat roughly one alarm per 10 minutes per operator as a reasonable average in steady operation. Under EEMUA 191, more than 10 alarms in 10 minutes marks an alarm flood. This guidance and the ASM study come mainly from U.S. and U.K. experience, plus international practice. Canadian facilities should validate them against their own staffing and regulations, as well as site conditions.

Where the HMI Fits in a Capital Project

The HMI is among the last things finished on many capital projects, yet nearly everything on screen comes from earlier data:

  • P&IDs and the instrument index identify each instrument and tag, with ranges and units.
  • Control narratives describe how each loop and sequence should behave.
  • Alarm setpoints and cause-and-effect logic set which alarms exist and what trips what.
  • Vendor package data supplies the tags and local screens for skids and packaged equipment.

The control system vendor or integrator typically builds the graphics, which are checked at factory acceptance testing (FAT) and site acceptance testing (SAT). After handover, changes to screens and alarms belong under management of change. When the same tag data is typed in spreadsheets, drawings, vendor files, and the HMI database, copies drift apart and mismatches surface late. A single source of truth reduces that duplicate entry.

Vista Projects’ instrumentation and controls engineering services cover the instrument data and control narratives that HMI screens are built from, along with the alarm settings, and they bring vendor packages together in a single, plant-wide control system. Engineering work in Alberta is regulated by APEGA, and work elsewhere by the equivalent provincial regulator.

Planning a site where vendor packages, instrument data, and the control system all need to line up? Talk to Our Experts

What HMIs Mean for Project and Site Teams

Project managers. The HMI is a schedule risk near the end of the project. Final graphics wait on tags and alarm limits, and on vendor package data, so late changes can mean rework and FAT retesting. Settle who owns the HMI philosophy and style guide early, and get operators reviewing screens before FAT.

Site supervisors. An HMI stop command is a control action, and it doesn’t isolate hazardous energy. In Alberta, OHS Code Part 15 requires an energy-isolating device that is secured and verified. Earlier Government of Alberta guidance confirms push buttons and selector switches don’t qualify. CSA Z460 is the Canadian lockout standard, and OSHA 29 CFR 1910.147 is the U.S. equivalent.

Edge Cases Worth Knowing on Industrial Sites

Cold weather. Some panel HMIs operate only down to 0°C, while extended-temperature units are rated to -20°C or lower. Check the operating rating against winter lows, not just the enclosure rating.

Direct sunlight. Standard panels are often rated around 300 cd/m², while screens for direct sun are usually specified at 1,000 cd/m² or more.

Mismatched vendor screens. If green means “running” on one skid’s screen and “closed” on another, operators are set up for errors. A site style guide that vendors must follow prevents this.

Cybersecurity. Most modern HMIs are networked computers. In October 2025, the Canadian Centre for Cyber Security warned that hacktivists are exploiting internet-accessible industrial control systems in Canada, and listed exposed HMIs among the components at risk. In the U.S., CISA issues regular HMI vulnerability advisories. The ISA/IEC 62443 series covers industrial control system security.

Frequently Asked Questions

What does HMI stand for?

HMI stands for human machine interface. In industrial settings, it means the screens and software operators use to monitor and control a process. A pump skid touchscreen and a control room workstation are both HMIs. Older documents sometimes use “MMI” (man-machine interface). “OIT” (operator interface terminal) is a related term for a simpler local terminal.

Can you use an HMI stop button for lockout?

No. An HMI stop command is a control-circuit action, not an energy-isolating device. Alberta’s OHS Code Part 15 requires isolating hazardous energy with a secured, verified energy-isolating device. The Code allows limited alternatives that give equal or greater protection. CSA Z460 is the Canadian standard for lockout. The U.S. general-industry equivalent, OSHA 29 CFR 1910.147, states that push buttons and selector switches, like other control-circuit devices, are not energy-isolating devices. Ordinary lockout needs a physical isolation point, secured with a lock and verified. That might be a disconnect or breaker, or a valve on a process line.

Why are modern HMI screens mostly grey?

Many modern HMI screens use neutral grey backgrounds so colour is free to signal abnormal conditions and alarms. A red or yellow element then stands out against muted tones. This high-performance approach comes from ASM Consortium guidance and fits within an ISA-101 lifecycle, though ISA-101 doesn’t require grey. As part of a complete high-performance design, it can help operators spot problems faster than colourful, P&ID-style screens.

Work With an Engineering Partner From Design Through Startup

An HMI doesn’t control the process, but it shapes what operators see and how fast they spot a problem, so the data behind each screen is worth getting right early. Vista Projects’ instrumentation and controls team works in a data-centric execution model, keeping tag data and alarm limits in one Owner-Controlled Digital Execution Environment. The HMI database and vendor packages then draw on the same current values as the control narratives. Fewer late tag changes mean less graphics rework and FAT retesting, which helps hold down the total installation cost (TIC) of a capital project and its total cost of ownership after handover. Behind that work sit more than 40 years of energy industry experience and integrated multi-discipline engineering, serving clients primarily across North America.

Talk to Our Experts

This article reflects Canadian standards and Alberta regulations, and licensing and code requirements differ in other provinces and jurisdictions. Confirm them with the authority having jurisdiction before you apply them to a project

Related Terminology

Data-centric Execution

Datacentric PDF DL